门架式堆取料机在铜冶炼中的生产实践

针对铜冶炼工艺的特点,从门架式堆取料机对前后工序衔接、结构、原理出发,介绍了其在熔炼炉系统和吹炼炉系统中的应用情况。经过试生产期的生产实践证明,门架式堆取料机具有场地利用率高、取料量大,自动化程度高和安全环保等优点。     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。     

动力蓄电池包挤压失效仿真与实验

为提高动力蓄电池包挤压仿真的精度，将延性损伤准则引入到有限元仿真，通过单轴拉伸试验、纯剪切试验与缺口件拉伸试验与有限元仿真，获得了某动力蓄电池包结构所用材料6061-T6铝合金的延性损伤参数。型材三点弯曲试验、动力蓄电池包挤压试验与有限元仿真的结果表明：输入延性损伤参数的有限元仿真结果与试验结果误差小，能较为准确地模拟铝合金损伤对结构承载性能的影响；不考虑材料失效的结果与试验结果误差较大。     

枞树型核电轮槽精铣刀制造技术优化设计

以枞树型叶根精铣刀为例,阐述了可换硬质合金型线刀体和刀片精铣刀的优化设计、制造工艺、建模及优化设计,进行切削过程加工策略优化和加工过程模拟,设计制造了锥柄专用工装及检测环规、磨削刀片后角专用工装,采用NUMROTO软件编制刀片加工工步。该项目研制的可换刀片精铣刀型线精度完全能达到进口铣刀水平,能满足大部分轮槽与叶根加工对型线精度的要求,可以大幅度节约刀具费用。     

一种液压摩擦焊机电液系统研究与试验

针对海上石油平台、海底输送管线维修的需要,提供了一种液压摩擦焊机液压和电器系统设计思路,通过参数计算、电液控制系统设计,研发了一种液压摩擦焊机,通过对DH38钢摩擦叠焊单元成型工艺试验,发现焊接接头拉伸强度达到了母材强度的76%以上,验证了液压摩擦焊机的可靠性能,通过该研究的应用,可对海上石油平台、海底输送管线的维修起到积极作用。     

基于极点配置的推力矢量伺服系统控制策略研究

针对推力矢量伺服系统提出了一种采用状态反馈对系统极点进行配置的方法,同时采用该方法设计了Luenberger状态观测器,在此基础上实现了伺服系统的稳态控制。通过仿真和实验表明,采用该方法设计的推力矢量伺服系统的性能优于基于输出反馈的PI-陷波滤波控制的系统性能。     

电液控制系统关键传感器的故障预警方法研究

为了保证电液控制系统的正常运行,对电液控制系统核心传感器部件的故障预警是关键一环,分析了传感器在电液控制系统的工作原理,得到了传感器在系统中的故障规律,为了对井下的电液控制系统中的核心传感器的故障进行预警和诊断,结合目前比较流行的传感器故障预警方法,以液压支架的压力传感器为例,提出了一个静态分析与动态分析融合的诊断方法,其核心是通过对传感器采集的数据进行分析,能有效预测压力传感器故障,提高电液控制系统的可靠性。     

A comprehensive review of renewable energy resources for electricity generation in Australia

Recently, renewable energy resources and their impacts have sparked a heated debate to resolve the Australian energy crisis. There are many projects launched throughout the country to improve network security and reliability. This paper aims to review the current status of different renewable energy resources along with their impacts on society and the environment. Besides, it provides for the first time the statistics of the documents published in the field of renewable energy in Australia. The statistics include information such as the rate of papers published, possible journals for finding relative paper, types of documents published, top authors, and the most prevalent keywords in the field of renewable energy in Australia. It will focus on solar, wind, biomass, geothermal and hydropower technologies and will investigate the social and environmental impacts of these technologies.     

Economic Evaluation of Power System Flexibility by Commercial Air Conditioner Control with Large Penetration of Photovoltaic Generation

High penetration of intermittent renewable energy such as photovoltaic (PV) and wind power could cause shortage of power system flexibility. Demand response is expected to help supply ancillary service instead of the conventional power plant. Commercial air conditioners are a promising responsive load for demand response because they account for a large proportion of power consumption in the power system. We calculate a system operation cost and hourly operation pattern of each power plant by using the optimal power generation model considering flexibility supply from controlling commercial air conditioner. We obtained the following results as an effect of commercial air conditioner control. (1) The power generation of oil fired power plants decreases at peak time and annual fuel cost of oil fired plant is reduced by approximately 30% at most in Kanto area. (2) The percentage of rated operation mode of LNG combined cycle plants increases. (3) Curtailed energy rate of PV decreases because a power storage amount by pumped hydropower generation increases. (4) Required battery capacity to reduce PV curtailed amount decreased by combining battery energy storage system in case of high penetration of PV.